This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
spiffchorder:2010-03-leather [2010/03/21 16:44]
spiffchorder:2010-03-leather [2010/03/23 21:30] (current)
Line 1: Line 1:
 ====== March 2010 Leather Desktop Chorder ====== ====== March 2010 Leather Desktop Chorder ======
-Sunday afternoon project. ​ This one uses the atmega168 chip.  It is built on a Radio Shack 276-150 printed circuit board which greatly reduces the need to run wires around. ​ It uses cherry ​keyswithches with replacement lighter weight springs.+Sunday afternoon project. ​ This right hand chorder ​uses the atmega168 chip.  It is built on a Radio Shack 276-150 printed circuit board which greatly reduces the need to run wires around. ​ It uses Cherry ​keyswithches with replacement lighter weight springs.  It was used to create and edit this wiki page.
 -Greg -Greg
-|{{spiffchorder:​2010.03.lc.ip.jpg|}}|| +|{{spiffchorder:​2010.03.lc.ip.jpg?400|}}| as tested prior to final glue up (Don't glue the case closed before you know it all works!)
-|{{spiffchorder:​2010.03.lc.keys.jpg|}}|Underside of the plastic board with keyswithches| +|{{spiffchorder:​2010.03.lc.keys.jpg?400|}}|Underside of the plastic board with keyswithches ​all wired
-|{{spiffchorder:​2010.03.lc.electronics_top.jpg|}}|circuit| +|{{spiffchorder:​2010.03.lc.electronics_top.jpg?400|}}|circuit ​- board has been cut away to fit in to the case.  Since switches are close, no pullup resistors are used in this build. ​ Keyswitches are wired to an eight pin sip socket ​
-|{{spiffchorder:​2010.03.lc.electronics_bottom.jpg|}}|underside of circuit| +|{{spiffchorder:​2010.03.lc.electronics_bottom.jpg?400|}}|underside of circuit ​- as you can see, only a few jumpers are needed and much more of the board could be cut away if need be
-|{{spiffchorder:​2010.03.lc.assembly_01.jpg|}}|foam | +|{{spiffchorder:​2010.03.lc.assembly_01.jpg?400|}}|foam ​keeps the keyswitch pins from contacting the circuit board and keeps everything in place
-|{{spiffchorder:​2010.03.lc.assembly_02.jpg|}}|circuit in place+|{{spiffchorder:​2010.03.lc.assembly_02.jpg?400|}}|circuit ​board in position
-|{{spiffchorder:​2010.03.lc.assembly_03.jpg|}}|more foam| +|{{spiffchorder:​2010.03.lc.assembly_03.jpg?400|}}|a little ​more foam to keep circuit board from moving around in the case
-|{{spiffchorder:​2010.03.lc.unwrapped_01.jpg|}}|exterior showing layers of leather| +|{{spiffchorder:​2010.03.lc.unwrapped_01.jpg?400|}}|exterior showing layers of leather ​- note that the thumb side of the chorder is quite a bit higher than the pinkie side and that it also is lower on the edge facing closer to your palm 
-|{{spiffchorder:​2010.03.lc.unwrapped_02.jpg|}}|exterior showing layers of learther+|{{spiffchorder:​2010.03.lc.unwrapped_02.jpg?400|}}|exterior showing layers of leather and slope of case
-|{{spiffchorder:​2010.03.lc.assembly_04.jpg|}}|trimmed ​and glue applied+|{{spiffchorder:​2010.03.lc.assembly_04.jpg?400|}}|leather ​trimmed, contact cement drying before attaching bottom. (I always put a date on it somewhere.)
-|{{spiffchorder:​2010.03.lc.assembly_05.jpg|}}|thin exterior layer glue applied+|{{spiffchorder:​2010.03.lc.assembly_05.jpg?400|}}|thin exterior layer (white fake leather) contact cement drying ​
-|{{spiffchorder:​2010.03.lc.assembly_06.jpg|}}|assembled| +|{{spiffchorder:​2010.03.lc.assembly_06.jpg?400|}}|assembled| 
-|{{spiffchorder:​2010.03.lc.final.jpg|}}|cleaned up|+|{{spiffchorder:​2010.03.lc.final.jpg?400|}}|cleaned up|
spiffchorder/2010-03-leather.1269204264.txt.gz · Last modified: 2010/03/21 16:44 by priestdo
Top of the Wiki www.chimeric.de Creative Commons License Valid CSS Driven by DokuWiki Recent changes RSS feed Valid XHTML 1.0